Speed-Rail, Grid Clamps & Box Truss Span Engineering

Nominal Pipe Size (NPS) vs. outer diameter math, 6061-T6 Schedule 40/80 cantilever spans, Cheeseborough torque limits, and 12-inch box truss tables.
GRIPEDIA FIELD GUIDE • Rigging & Overhead Physics • HOLLYWOOD, CALIFORNIA, USA

Speed-Rail, Grid Clamps & Box Truss Span Engineering

Nominal Pipe Size (NPS) vs. outer diameter math, 6061-T6 Schedule 40/80 cantilever spans, Cheeseborough torque limits, and 12-inch box truss tables.

Direct Field Answer: Motion picture overhead grids and menace spans depend on 1-1/4" NPS (1.660" OD) and 1-1/2" NPS (1.900" OD) extruded 6061-T6 structural aluminum Speed-Rail rated to 35,000 psi yield strength. Center point load capacity ($CPL$) drops inversely with span length ($L$), falling from 362 lbs at 6 ft to 181 lbs at 12 ft—the threshold where box truss or center drop support becomes mandatory.

1. Nominal Pipe Size (NPS) vs. True Outside Diameter

Never gauge cinema rigging clamps by nominal plumber pipe labels. Every 1-1/2" Speed-Rail fitting, grid clamp, and Cheeseborough coupler clamps onto 1.900" (48.26 mm) outer tubing diameter.

Nominal Size (NPS)True Outer Diameter (OD)Schedule & WallMaterial AlloyWeight per FootSection Modulus ($Z$)
1-1/4" NPS1.660 in (42.16 mm)Sched 40 (0.140" wall)6061-T6 Aluminum0.786 lbs/ft0.235 in³
1-1/4" NPS1.660 in (42.16 mm)Sched 80 (0.191" wall)6061-T6 Aluminum1.037 lbs/ft0.291 in³
1-1/2" NPS1.900 in (48.26 mm)Sched 40 (0.145" wall)6061-T6 Aluminum0.940 lbs/ft0.326 in³
1-1/2" NPS1.900 in (48.26 mm)Sched 80 (0.200" wall)6061-T6 Aluminum1.256 lbs/ft0.412 in³
1-1/2" Galvanized1.900 in (48.26 mm)Sched 40 (0.145" wall)ASTM A53 Steel2.720 lbs/ft0.326 in³

2. Diagram: Simply Supported Span Deflection & Clamp Geometry

GRID CLAMP GRID CLAMP CPL LOAD (LBS) CPL = (4 × F_b × Z) / L | 1-1/2" SCHED 40 (1.900" OD) 6 ft Span = 362 lbs | 10 ft Span = 217 lbs | 12 ft Span = 181 lbs (0.88" sag)

3. Allowable Pipe Span Loads vs. 12-Inch Box Truss

Unsupported Span ($L$)1-1/2" Sched 40 CPL1-1/2" Sched 40 Sag ($\delta$)12" Box Truss CPLAction Rule
6 ft (72 in)362 lbs0.22 in—Standard overhead lamp span
8 ft (96 in)271 lbs0.39 in—Dual-head wall spreader safe zone
10 ft (120 in)217 lbs0.61 in2,780 lbsSingle pipe max comfortable lamp span
12 ft (144 in)181 lbs0.88 in—Visible sag threshold; add bridle pick
16 ft (192 in)135 lbs1.56 in~1,700 lbsCenter vertical drop / truss required
20 ft (240 in)Not Rated UnbracedExcess Sag1,365 lbsMandatory 12" or 20.5" Box Truss

4. Field Torque & Coupler Rules

  1. Fixed ($90^\circ$) vs. Swivel Cheeseboroughs: Forged fixed couplers rate to 2,200 lbs slip load; swivel diagonal couplers rate to 1,650 lbs slip load. Torque 1/2" nuts carefully to 30–35 ft-lbs using a standard box ratchet—never a cheater bar.
  2. Almag 535 Hollaender Slip-On Fittings: Internal hardened set screws bite into extruded aluminum at 15–17 ft-lbs. Always clean pipe ends before seating internal splices (#17 couplings, 600 lbs max pull) and back every overhead pipe with safety wire or spanset choke.

Hardware Engineered for This Rigging Standard

Frequently Asked Set Questions

Q: What is the exact outer diameter of 1-1/2 inch Schedule 40 Speed-Rail?
Nominal Pipe Size (NPS) 1-1/2 inch aluminum or galvanized steel pipe measures 1.900 inches (48.26 mm) outside diameter—not 1.500 inches. Always order 1-1/2 inch NPS Grid Clamps and Cheeseboroughs for 1.900 inch OD pipe.
Q: What torque should be used when tightening aluminum Cheeseborough nuts on 6061-T6 pipe?
Tighten standard 1/2-inch scaffold clamp nuts with a 7/8-inch ratchet wrench to 30 to 35 ft-lbs. Over-torquing crushes 6061-T6 Schedule 40 aluminum pipe walls and creates stress fractures.
Q: When should a grip crew upgrade from single 1-1/2 inch Speed-Rail to 12-inch aluminum box truss?
Upgrade to 12-inch box truss whenever unsupported horizontal spans exceed 12 feet (where single pipe midspan sag reaches 0.88 inches) or whenever overhead fixture point loads exceed 200 lbs.
VERIFIED IN HOLLYWOOD, CALIFORNIA, USA • EST. 1962

Put This Engineering Into Practice On Set

Sign in to leave a comment
The History of Hollywood Cinema Grip (1962–Present): Norms Studio Equipment Origins
From Norman Bernard Hess supplying Paramount, Warner Bros., Universal & Fox in 1962, to the American Grip Mother Tree, Taylor Ngo's 2009 re-engineering, and the 2025 Lifetime Warranty.